Quick Answer: What’S The Difference Between Waste And Backwash?

Why would you use recirculate on pool filter?

Recirculate – This setting is used to troubleshoot problems with the filter sand and is especially useful if you are battling an algae bloom.

The water will circulate in the pool normally, but will bypass the filter sand.

Waste – Used primarily while vacuuming to remove heavy debris from the floor of the pool..

How do I vacuum to waste?

How do I vacuum to waste?Turn off the pump.Move the multiport valve to the waste setting.Turn the pump back on. … Close all skimmer lines except for one.Close your main drain down to 50%Set up your vacuum the way you normally would for regular vacuuming.More items…

How many hours a day should a pool pump run?

approximately 8 hoursNow that you understand your pool’s turnover rate and have ensured that your pump is up to speed (do you see what we did?), it’s time to begin planning when to run your pump. Every pool must turn over at least once a day, so most pool pumps should run approximately 8 hours a day.

Should I backwash after shocking pool?

Backwash only as needed. Brush the pool vigorously, several times after shocking the pool. Do not use a solar blanket until chlorine and pH level are normal. If chlorine level drops to zero within 24 hours, Repeat the shock treatment.

Do you vacuum a pool on backwash or waste?

You can vacuum a pool on backwash, in theory at least, but it would have no benefit. The water would be pumped backwards through the filter, trapping much of the dirt, before passing out through the backwash hose. This dirt would then end up back in the pool once the pump was back on the filter setting.

Do I need to rinse after backwash?

Remember to “rinse the filter after backwashing to recompact the sand in the filter to ensure effective filtration. Consider cleaning your filter sand once a year using HTH® Color indicator Filter cleaner.

What is waste setting on pool filter?

The Waste setting allows water to enter the filter, but bypass the filter media, and be sent completely out of the filtration system. Important: Make sure you’re disposing of expelled pool water correctly so you’re not damaging your yard or the environment.

Where does the water go when you backwash a pool?

Backwash pools directly into the private sewer cleanout on your property instead of into the storm gutter. If you are on septic and don’t have sufficient area to discharge onto your property, try the following: Hire a contractor to pump the pool water into a truck to be hauled offsite.

What does a backwash do?

Well, as the name suggests, backwashing involves reversing the flow of water through your filter media, be it Zeoplus, sand, glass pearls or diatomaceous earth (DE). This dislodges dirt and debris that may have become trapped, and flushes it out through your multiport valve waste line.

How long should you backwash a pool?

2 minutesSet the filter valve handle to the BACKWASH pool position and ensure the handle locks in place. Turn on the pump and backwash for 2 minutes or until the water in the sight glass (located on the filter) is running clear. Turn Off the Pump.

Do you backwash after vacuuming to waste?

Once you have finished vacuuming, turn off your pump. … If you vacuumed on waste, you will need to turn your filter to the “rinse” setting, turn on the pump and let it run for about 30 seconds, and then turn the pump back off. Make sure to set your filter back to “filter” after you do this.

Should I run my pool pump at night or day?

Running your pool pump during the day is good because that’s when the sun is out. UV rays are eating up the chlorine, so it is good to have the pump running to counteract the sun’s effects. A pro for night time would be that it’s off-peak utility hours. It’s cheaper to run the pool pump at night.

How much will a pool raise my electric bill?

Running costs are typically between $800.00 & $1200.00 per year at 2018/19 prices. A typical backyard swimming pool using a 1100 watt pool pump can add up to 17% to an electricity bill. This cost can be offset by installing solar panels, which can also add value to the house.

Can you backwash a pool too much?

Backwashing a filter too frequently will keep the sand so free of dirt buildup that it will not have the ability to remove the smaller particles of dirt and they will simply pass through sometimes causing cloudiness in water.

Does a pool pump use a lot of electricity?

Outside of the air conditioner, the pool pump is the largest electricity consumer in the average pool-containing home. According to the study, at the national average of 11.8 cents per KWh, a pool pump alone can add as much as $300 a year to an electric bill.

What happens if you don’t backwash your pool?

Backwashing tips Backwashing can result in a loss of water. While this is unavoidable, you can minimize the amount of water you lose by not overdoing the backwashing process. Keep a close eye on the color of the water through the view glass and stop the minute it becomes clear.

Is it OK to run pool pump 24 hours a day?

To conclude, running your pool pump for 24 hours is not a bad thing. It is actually ideal to do so. But since it can significantly increase pool maintenance cost, we suggest only running your pump for 12 hours or less, depending on the size of your pool and the efficiency of your pump.